Many people know how to apply nail polish. Different manicurists have different techniques when doing nails. Therefore, the works presented by manicurists are definitely different. Many people do not know how to use nail polish for manicures. Many people want to learn how to make their hands more attractive. In fact, the correct way to do nail polish manicures is not as difficult as imagined. What are the correct steps for doing gel nail polish manicure? Let’s take a look at it next. 1. Remodeling First use a standard file to trim the nails into the designed shape. Then make sure to use a sponge file to remove and clean the nail clippings under the nail tip to prevent the nail polish from sticking to the nail clippings and causing the nail tip to quickly lift and fall off. Trim dead skin: first use a cuticle pusher to push up the excess dead skin on the edge of the nail, and then use a cuticle scissors to trim it clean to prevent nail polish from sticking to the dead skin or flesh and causing the back edge to quickly lift up and fall off. Scrape and clean the nail surface: Then use the rough surface of the sponge to scrape the surface of the nail, focusing on the edges and tips of the nail. If you encounter nails that are prone to falling off or are soft and thin, be sure to use a standard rough file to grind them carefully. Note: This step can be completed quickly without affecting the quality because: in addition to shaping and carving the nail surface, it requires careful processing. To clean the nail dandruff, you can just pass it lightly when trimming your nails (remove the dead skin. Some girls have less dead skin at the nail edge, so they can do a simple trim or no trimming. Just gently push the dead skin up and proceed to the next step. To clean the nail dandruff, you can just pass it lightly when trimming your nails. 2. Apply bonding agent. The correct operation process of nail polish glue: The binder is water-based, so do not take too much to avoid it flowing or not drying. The bonding agent only needs to be applied around the edges of the nail and the tip of the nail, because the focus points are the surrounding areas and the tip of the nail, which are also the parts that are prone to falling off. When removing nail polish, firstly, it is easier to remove, secondly, it will not cause damage to the customer's nail surface, and finally, pay attention to the edging, so there is no need for lighting. Note: This step can be omitted in case of speed increase because: some brands of adhesive binder and primer are two-in-one, so you can only apply the primer. 3. Apply primer The correct operation process of nail polish is to apply a full amount of base glue, and do not apply it too thinly around the edges. If it is applied too thinly, it will lack supporting strength and cause it to break and fall off from the edges like pancakes. It is recommended to use the half-application method, applying from bottom to top (apply the lower half of the nail first and then apply the entire surface upwards, so that the color saturation is stronger and more uniform from top to bottom), and finally pay attention to the edge. The LED light must be applied for 1 minute and the UV light must be applied for 3 minutes. (Uniform lighting) 4. Apply nail polish The correct operation process of nail polish gel is to apply nail polish normally in a normal amount. Don’t use too much, as too much will cause uneven application. Similarly, add a little more volume around the edges so that the edges don't look blurry and look more solid. To prevent the chunks from falling off. Finally, pay attention to the edging, expose with LED light for 30 seconds and UV light for 1 minute. (Shine the light evenly) Then apply a second coat as above, the color saturation will be enhanced. 5. Apply the sealant The correct operating procedure for nail polish is to apply a full layer of nail polish, do not apply it too thinly on the edges, and completely cover the color glue. Apply it on the surface of the nails, and finally pay attention to the edges. The LED light must be applied for 1 minute, and the UV light must be applied for 3 minutes. (Uniform lighting) Also remember that if the customer's nails are very thin, it is recommended to apply 3 more coats of base glue to reinforce them before applying the color glue. Never apply too much top coat. First, after reinforcement, it has strong support and is not easy to fall off. Second, if you apply three coats of topcoat, it will be troublesome to remove, because the density of the base coat of all nail polish is not as high as the topcoat, so the base coat is easy to remove. The above is the standard operating procedure for nail polish. |
<<: How do beginners use eyebrow powder to draw eyebrows?
>>: What should I do if nail polish is not applied evenly?
Fruit acid peeling is a beauty method that is pop...
Nowadays, many people still lack knowledge about ...
If we have a lot of cold hair on our face, it wil...
Having spots on the face is a problem that bother...
Wrinkles may appear on the skin due to aging, dec...
Maybe due to various reasons, we have to leave so...
Many people like to do a lot of things on their f...
Love of beauty is in all of our nature. The devel...
As technology in our daily lives continues to imp...
What female friends are most concerned about is t...
Garlic is the most common condiment in our lives....
Acne has always been the nemesis of people who lo...
The skin on the human face is very fragile. If it...
I don’t know if you have noticed this problem: so...
Skin care is very important at any age. If the st...